AEG ARE I2 Operations Instructions Page 88
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
86
TYPE VOLTAGE ...P400... 230 volts -20% to 400 volts +10%
...P500... 230 volts -20% to 500 volts +10%
...P690... 500 volts -20% to 690 volts +10%
MAINS FREQUENCY all models 45Hz to 65Hz
LOAD DESCRIPTION ohmic load (minimum 100W)
ohmic load R
hot
/R
cold
ratio up to 20 (MOSI operation)
transformer load
TRANSFORMER The induction of the load side transformer should not exceed
1.45T in case of mains overvoltage when using grain-oriented,
cold-rolled plates. This corresponds to a nominal induction of
approx. 1.3T.
OPERATING MODES TAKT = full oscillation clock = default setting for the
models 1P, 2P and 3P
VAR = phase-angle firing = only for the models 1P and 3P
SSSD = soft-start-soft-down; a combination of
„VAR“ and „TAKT“, for the models 1P, 2P and 3P,
i.e. reduced mains surge load
VSC_VAR = phase-angle firing in voltage sequence control
SET POINT INPUTS The power controller Thyro-P has 4 set point inputs.
The set point inputs are indirectly connected to the mains
(SELV, PELV).
Set points 1, 2: external set point input
signal ranges:
0(4) - 20 mA Ri = ca. 250 V / max. 24mA*
0 - 5 V Ri = ca. 8,8 kV / max. 12V
0 - 10 V Ri = ca. 5 kV / max. 12V
* refer to ”ATTENTION” in chapter 2.2
Set point 3: connection for fiber optic (LL) from the super-
ordinate PC or automation system
Set point 4: set point assignment via RS232
(for instance LBA-2)
ANALOG OUTPUTS
3 outputs: signal level 0-10 V, 0-20mA or 4-20mA. The maximum
burden voltage is 10V
CONTROL CHARACTERISTIC
The control characteristic is established by the maximum value
of the dimensions to be controlled and the key values of the
set point. Using these key values, the linear control characte-
ristic may be set at will.
Every controller (for instance temperature controller), whose
output signal is in the range of 0-20mA/0-5V/0-10V may be
easily adapted to the power controller.
CONTROL TYPES Voltage control U
rms
Voltage control U
2
rms
= default setting
Current control I
rms
Current control I
2
rms
11. TECHNICAL DATA
- THYROP 1
- SAFETY INSTRUCTIONS 4
- TABLE OF CONTENTS 7
- SAFETY REGULATIONS 10
- INTENDED USE 11
- LIABILITY 11
- GUIDELINES 12
- VALIDITY 13
- HANDLING 13
- WARRANTY 13
- INTERNET 14
- COPYRIGHT 14
- 1. INTRODUCTION 15
- 1.3 TYPE DESIGNATION 16
- 2. FUNCTIONS 17
- V / max. 24mA) see ATTENTION 19
- V / max. 12V) 19
- ATTENTION 19
- Set point 20
- Register 20
- 2.3 CONTROL TYPES 21
- 2.3.1 CONTROLLED VALUE 21
- 2.4 INDICATIONS 22
- 2.4.1 LED INDICATIONS 22
- 2.5 MONITORING 23
- 2.5.2. LOAD MONITORING 24
- 2.5.2.2 RELATIVE MONITORING 24
- 2.5.2.3 OVERVIEW MONITORING 27
- („SHORT CIRCUIT MONITORING“) 27
- 2.5.4 FAN MONITORING 28
- 3. OPERATION 29
- Thyro-P Thyro-P 30
- 3.1.4 EASYSTART 31
- 3.1.6 LOAD / SAVE DATA 31
- 3.1.10 LANGUAGES 33
- 3.2 LBA-2 TOOL 33
- 3.2.1 OVERVIEW 34
- 3.2.2 LANGUAGES 35
- 3.2.3 SELECT LOG FILE FOLDER 35
- 3.2.4 CALENDAR NAVIGATION 35
- 3.2.5 TIME AXIS 36
- 3.2.6 VALUE AXES 36
- 3.2.7 VALUES DISPLAY 37
- 3.2.8 EVENT REPORTS 37
- 3.2.9 PDF EXPORT 37
- 3.2.10 EXAMPLE 37
- 3.4 THYRO-TOOL FAMILY 38
- 3.5.1 LBA-2 40
- 3.5.2 THYRO-TOOL FAMILY 40
- 3.6 LBA-2 MENU STRUCTURE 42
- TAB. 6 LBA-2 MENU STRUCTURE 46
- 4. EXTERNAL CONNECTIONS 47
- 4.4 RESET 48
- 4.5 CONTROLLER INHIBIT 48
- 4.6 QUIT 48
- 4.7 SET POINT VALUE INPUTS 49
- 4.8 ASM INPUT 49
- 4.9 dASM INPUT - dASM OUTPUT 49
- 4.10 ANALOG OUTPUTS 49
- 4.11 CURRENT TRANSFORMER 50
- 4.12 VOLTAGE TRANSFORMER 52
- 4.14 SYNCHRONIZATION 54
- X7.1 (-) 56
- X7.2 (+) 56
- 5. INTERFACES 57
- 5.1 RS232 INTERFACE 58
- 5.2 FIBER OPTIC INTERFACE 59
- fiber optic receiver (LLE) X31 60
- 5.3 BUS INTERFACES (OPTIONAL) 62
- FOR COMMISSIONING 63
- OTHER FEATURES 63
- APPROACH FOR dASM APPLICATION 63
- Unit 1 (M) Unit 2 Unit 3 64
- X41 X40 X41 X40 64
- Unit 1 (M) Unit 2 Unit 3 (M) 66
- Controller 1 70
- Controller 2 70
- BASIC CONNECTIONS 71
- 8. CONNECTING DIAGRAMS 73
- Thyro-P 1P 74
- Thyro-P 2P 75
- Thyro-P 3P 76
- Thyro-P 1P...VSC 2 77
- Thyro-P 1P...VSC 3 78
- 9. SPECIAL REMARKS 81
- 9.3 COMMISSIONING 82
- 9.4 SERVICE 82
- 9.5 CHECKLIST 82
- 10. TYPE OVERVIEW 84
- 10.2 TYPE RANGE 500 VOLT 85
- 10.3 TYPE RANGE 690 VOLT 87
- 11. TECHNICAL DATA 88
- Power control P 89
- 12. DIMENSIONAL DRAWINGS 92
- Stat. Alteration Date Name 95
- 2000000282 MB 98
- Vorderansicht / front view 100
- Seitenansicht / side view 100
- Seitenansicht / sideview 101
- 1000 HF 102
- 2 000 000 294 MB 103
- 13. ACCESSORIES AND OPTIONS 105
- CAUTION 106
- and Thyro-P 111
- are trademarks of Advanced 111
Related products and manuals for Power supply units AEG ARE I2
(42 pages)© 2020, manymanuals.com. All rights reserved. | 1.565 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals