AEG ARE I2 Operations Instructions Page 48
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
46
CAUTION
The pulled plug has mains voltage of the load circuit! The new connecting lines must be fused
according to the applicable regulations (for applicable plug, see chapter 13).
4.3 POWER SUPPLY FOR THE VENTILATOR
With Thyro-P Thyristor Power Controllers furnished with integrated ventilators (HF types), the venti-
lator must be supplied with a voltage of 230V 50/60Hz according to the connecting plans and the
dimensional drawings. The ventilator’s power consumption is given in chapter 11 TECHNICAL
DATA.
ATTENTION
The ventilator must run when the Power Controller is switched on.
4.4 RESET
The input RESET (terminals X5.2.12-X5.1.14) is separated from the remaining system by an opto-
electronic coupler. By opening the RESET jumper the Thyristor Power Controller is locked (load:
24V/20mA), i.e. the power sections are no longer triggered. On activating RESET, LED “ON” lights
up red.
Functional procedure:
TERMINALS FUNCTION
X5.12-14 closed Enables the device
X5.12-14 open Device is out of operation, communication via interfaces not possible
TAB. 8 RESET
The hardware RESET must be applied when synchronizing the software of several Power Controllers
(chapter 6.3 SOFTWARE SYNCHRONIZATION). If the Power Controller is equipped with a Bus
option, a Bus RESET also ensues from the hardware RESET. Apart from opening the jumper terminal
X5.2.12-X5.1.14, the hardware RESET is also activated by supply voltage OFF or by reducing the
supply voltage at the Power Controller (A70-X1) to below 160V.
4.5 CONTROLLER INHIBIT
The input controller lock (terminals X5.2.15 and X5.1.14) is electrically identical to the input RESET
(electrical data as under 4.4.).
ATTENTION
When activating controller lock, the LED „PULSE LOCK“ is lit and the control device remains com-
pletely in operation. The total set point is therefore without effect, but the min. limiting values (TS-
MIN, HIME) remain active. This enables securing a certain quantity of electrical energy at the load.
TERMINALS FUNCTION
X5.15-14 closed power controller operating
X5.15-14 open control pulses OFF (default value) or pulse limit
TAB. 9 CONTROLLER LOCK
All other functions of the power controller remain in operation. The state of the signalling relay
does not change (parameter-dependent) and communications remains active. After closing the
controller lock jumper, the controller is back in operation.
4.6 QUIT
The input acknowledge (Quit, X5.2.19) has a circuit identical with the input RESET. It must be
- THYROP 1
- SAFETY INSTRUCTIONS 4
- TABLE OF CONTENTS 7
- SAFETY REGULATIONS 10
- INTENDED USE 11
- LIABILITY 11
- GUIDELINES 12
- VALIDITY 13
- HANDLING 13
- WARRANTY 13
- INTERNET 14
- COPYRIGHT 14
- 1. INTRODUCTION 15
- 1.3 TYPE DESIGNATION 16
- 2. FUNCTIONS 17
- V / max. 24mA) see ATTENTION 19
- V / max. 12V) 19
- ATTENTION 19
- Set point 20
- Register 20
- 2.3 CONTROL TYPES 21
- 2.3.1 CONTROLLED VALUE 21
- 2.4 INDICATIONS 22
- 2.4.1 LED INDICATIONS 22
- 2.5 MONITORING 23
- 2.5.2. LOAD MONITORING 24
- 2.5.2.2 RELATIVE MONITORING 24
- 2.5.2.3 OVERVIEW MONITORING 27
- („SHORT CIRCUIT MONITORING“) 27
- 2.5.4 FAN MONITORING 28
- 3. OPERATION 29
- Thyro-P Thyro-P 30
- 3.1.4 EASYSTART 31
- 3.1.6 LOAD / SAVE DATA 31
- 3.1.10 LANGUAGES 33
- 3.2 LBA-2 TOOL 33
- 3.2.1 OVERVIEW 34
- 3.2.2 LANGUAGES 35
- 3.2.3 SELECT LOG FILE FOLDER 35
- 3.2.4 CALENDAR NAVIGATION 35
- 3.2.5 TIME AXIS 36
- 3.2.6 VALUE AXES 36
- 3.2.7 VALUES DISPLAY 37
- 3.2.8 EVENT REPORTS 37
- 3.2.9 PDF EXPORT 37
- 3.2.10 EXAMPLE 37
- 3.4 THYRO-TOOL FAMILY 38
- 3.5.1 LBA-2 40
- 3.5.2 THYRO-TOOL FAMILY 40
- 3.6 LBA-2 MENU STRUCTURE 42
- TAB. 6 LBA-2 MENU STRUCTURE 46
- 4. EXTERNAL CONNECTIONS 47
- 4.4 RESET 48
- 4.5 CONTROLLER INHIBIT 48
- 4.6 QUIT 48
- 4.7 SET POINT VALUE INPUTS 49
- 4.8 ASM INPUT 49
- 4.9 dASM INPUT - dASM OUTPUT 49
- 4.10 ANALOG OUTPUTS 49
- 4.11 CURRENT TRANSFORMER 50
- 4.12 VOLTAGE TRANSFORMER 52
- 4.14 SYNCHRONIZATION 54
- X7.1 (-) 56
- X7.2 (+) 56
- 5. INTERFACES 57
- 5.1 RS232 INTERFACE 58
- 5.2 FIBER OPTIC INTERFACE 59
- fiber optic receiver (LLE) X31 60
- 5.3 BUS INTERFACES (OPTIONAL) 62
- FOR COMMISSIONING 63
- OTHER FEATURES 63
- APPROACH FOR dASM APPLICATION 63
- Unit 1 (M) Unit 2 Unit 3 64
- X41 X40 X41 X40 64
- Unit 1 (M) Unit 2 Unit 3 (M) 66
- Controller 1 70
- Controller 2 70
- BASIC CONNECTIONS 71
- 8. CONNECTING DIAGRAMS 73
- Thyro-P 1P 74
- Thyro-P 2P 75
- Thyro-P 3P 76
- Thyro-P 1P...VSC 2 77
- Thyro-P 1P...VSC 3 78
- 9. SPECIAL REMARKS 81
- 9.3 COMMISSIONING 82
- 9.4 SERVICE 82
- 9.5 CHECKLIST 82
- 10. TYPE OVERVIEW 84
- 10.2 TYPE RANGE 500 VOLT 85
- 10.3 TYPE RANGE 690 VOLT 87
- 11. TECHNICAL DATA 88
- Power control P 89
- 12. DIMENSIONAL DRAWINGS 92
- Stat. Alteration Date Name 95
- 2000000282 MB 98
- Vorderansicht / front view 100
- Seitenansicht / side view 100
- Seitenansicht / sideview 101
- 1000 HF 102
- 2 000 000 294 MB 103
- 13. ACCESSORIES AND OPTIONS 105
- CAUTION 106
- and Thyro-P 111
- are trademarks of Advanced 111
Related products and manuals for Power supply units AEG ARE I2
(42 pages)Ce-niehoff-co N1224 Alternator Regulator Changeout Instructions manuels
Manuels d'utilisation et guides de l'utilisateur pour Matériel Ce-niehoff-co N1224 Alternator Regulator Changeout Instructions.
Nous fournissons des manuels en pdf 1 Ce-niehoff-co N1224 Alternator Regulator Changeout Instructions à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comments to this Manuals