AEG ARE I2 Operations Instructions Page 82
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
80
Afterwards safe gaps (according to IP20) have to be cut into the covers.
Please be consider that an adequate IP20 protection has to be secured.
Then the according coverages have to be fixed again on the device.
9.3 COMMISSIONING
The device must be connected to the mains and the associated load according to the wiring
diagrams.
REMARK
If the units Thyro-P 1P (or Thyro-P 3P in „open delta“) and/or Thyro-P 2P are operated at over 600
V and without load at the output side, voltages can occur above input voltage at the connection
points U2,V2 and W2. In this case, additional 690V snubber boards are to be used (see chapter 13
ACCESSORIES AND OPTIONS).
Depending on connection system of the load (star, delta, etc.), it must be ensured that the load vol-
tage transformers in the power sections are wired correctly (terminal strip X1 of the power section).
The correct terminals may be found in the connecting diagrams.
On delivery, the device is parameterized adjusted to the respective power section. The operating
mode TAKT (Thyro-P 1P / Thyro-P 2P) is set. If a different operating mode is desired, then the user
must set this using the LBA-2, PC, etc. Generally, the standard parameters (see menu list) should
be reviewed and adjusted to the respective conditions for use by the user (for instance operating
mode, control mode, limitations, monitoring, times, characteristics, actual value outputs, fault indi-
cations, relays, time and date, etc.).
Besides the load, some control signals must be connected as well (refer to chapter 4). The following
signals are always required for operation of the device:
Set point (terminal 10 or 11/or via interfaces)
RESET (on ground, on terminal 12, jumper set as standard)
Regular inhibit (on ground, on terminal 15, jumper set as standard)
If the RESET is not connected, then the device is in reset state and is not operating (LED „ON“
shows red light), i.e. no communications is possible via interface. Further details of the RESET are
described in chapter 4.4. If the regulator inhibit is not connected, then the device is fully operable,
but the power section is only controlled using the values of the minimal limitations (LED „PULSE
LOCK“ is on). Further details on the regulator inhibit may be found in the chapter 4.5 of the same
name.
ATTENTION
The controller lock may also be set via the interfaces!
ATTENTION
The control device is to be operated only with casing.
9.4 SERVICE
The devices delivered have been tested according to the state of the art and have been produced
to a high quality standard (DIN EN ISO 9001). In the event of any faults or problems despite such
controls, please contact our technical support team (see page 12 CONTACT).
9.5 CHECKLIST
No frontside LED is on:
• for 690V devices, the power supply for the control device A70 to be provided by the customer is
missing. (Attention, maximum nominal input voltage 500V)
- THYROP 1
- SAFETY INSTRUCTIONS 4
- TABLE OF CONTENTS 7
- SAFETY REGULATIONS 10
- INTENDED USE 11
- LIABILITY 11
- GUIDELINES 12
- VALIDITY 13
- HANDLING 13
- WARRANTY 13
- INTERNET 14
- COPYRIGHT 14
- 1. INTRODUCTION 15
- 1.3 TYPE DESIGNATION 16
- 2. FUNCTIONS 17
- V / max. 24mA) see ATTENTION 19
- V / max. 12V) 19
- ATTENTION 19
- Set point 20
- Register 20
- 2.3 CONTROL TYPES 21
- 2.3.1 CONTROLLED VALUE 21
- 2.4 INDICATIONS 22
- 2.4.1 LED INDICATIONS 22
- 2.5 MONITORING 23
- 2.5.2. LOAD MONITORING 24
- 2.5.2.2 RELATIVE MONITORING 24
- 2.5.2.3 OVERVIEW MONITORING 27
- („SHORT CIRCUIT MONITORING“) 27
- 2.5.4 FAN MONITORING 28
- 3. OPERATION 29
- Thyro-P Thyro-P 30
- 3.1.4 EASYSTART 31
- 3.1.6 LOAD / SAVE DATA 31
- 3.1.10 LANGUAGES 33
- 3.2 LBA-2 TOOL 33
- 3.2.1 OVERVIEW 34
- 3.2.2 LANGUAGES 35
- 3.2.3 SELECT LOG FILE FOLDER 35
- 3.2.4 CALENDAR NAVIGATION 35
- 3.2.5 TIME AXIS 36
- 3.2.6 VALUE AXES 36
- 3.2.7 VALUES DISPLAY 37
- 3.2.8 EVENT REPORTS 37
- 3.2.9 PDF EXPORT 37
- 3.2.10 EXAMPLE 37
- 3.4 THYRO-TOOL FAMILY 38
- 3.5.1 LBA-2 40
- 3.5.2 THYRO-TOOL FAMILY 40
- 3.6 LBA-2 MENU STRUCTURE 42
- TAB. 6 LBA-2 MENU STRUCTURE 46
- 4. EXTERNAL CONNECTIONS 47
- 4.4 RESET 48
- 4.5 CONTROLLER INHIBIT 48
- 4.6 QUIT 48
- 4.7 SET POINT VALUE INPUTS 49
- 4.8 ASM INPUT 49
- 4.9 dASM INPUT - dASM OUTPUT 49
- 4.10 ANALOG OUTPUTS 49
- 4.11 CURRENT TRANSFORMER 50
- 4.12 VOLTAGE TRANSFORMER 52
- 4.14 SYNCHRONIZATION 54
- X7.1 (-) 56
- X7.2 (+) 56
- 5. INTERFACES 57
- 5.1 RS232 INTERFACE 58
- 5.2 FIBER OPTIC INTERFACE 59
- fiber optic receiver (LLE) X31 60
- 5.3 BUS INTERFACES (OPTIONAL) 62
- FOR COMMISSIONING 63
- OTHER FEATURES 63
- APPROACH FOR dASM APPLICATION 63
- Unit 1 (M) Unit 2 Unit 3 64
- X41 X40 X41 X40 64
- Unit 1 (M) Unit 2 Unit 3 (M) 66
- Controller 1 70
- Controller 2 70
- BASIC CONNECTIONS 71
- 8. CONNECTING DIAGRAMS 73
- Thyro-P 1P 74
- Thyro-P 2P 75
- Thyro-P 3P 76
- Thyro-P 1P...VSC 2 77
- Thyro-P 1P...VSC 3 78
- 9. SPECIAL REMARKS 81
- 9.3 COMMISSIONING 82
- 9.4 SERVICE 82
- 9.5 CHECKLIST 82
- 10. TYPE OVERVIEW 84
- 10.2 TYPE RANGE 500 VOLT 85
- 10.3 TYPE RANGE 690 VOLT 87
- 11. TECHNICAL DATA 88
- Power control P 89
- 12. DIMENSIONAL DRAWINGS 92
- Stat. Alteration Date Name 95
- 2000000282 MB 98
- Vorderansicht / front view 100
- Seitenansicht / side view 100
- Seitenansicht / sideview 101
- 1000 HF 102
- 2 000 000 294 MB 103
- 13. ACCESSORIES AND OPTIONS 105
- CAUTION 106
- and Thyro-P 111
- are trademarks of Advanced 111
Related products and manuals for Power supply units AEG ARE I2
(42 pages)© 2020, manymanuals.com. All rights reserved. | 1.510 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals