AEG ARE I2 Operations Instructions Page 50
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
48
tions, limiting and the influence of operating modes with SSSD and MOSI) give the actual value
signals dynamic rations which can be smoothed with a smoothing stage. The MEAN (VALUE) para-
meter is applied here. The following setting is recommended: MEAN(VALUE) = 25.
4.11 CURRENT TRANSFORMER
By standard, each power section of the power controller has a current transformer. When using
external current transformers, for instance on the secondary side of a transformer, these must be
connected to the terminals X7.1 and X7.2 and terminated using a load resistor.
Each external voltage transformer must be connected with an load resistor.
CAUTION
Danger of electric shocks.
Current transformers must not be used without load resistors (secondary side), otherwise high
voltages can occur at the terminals.
ATTENTION
Danger of damaging Thyro-P.
Current transformers must not be used without load resistors (secondary side), otherwise high
voltages can occur at the terminals.
The load resistor must be designed so that at nominal current a voltage drop of 0.9 - 1.1Vrms
occurs at the burden resistance.
The value of the used load resistor has to be entered with Thyro-Tool Family or LBA-2 in parameter
U_Load resistor.
REMARK
The internal current transformers of Thyro-P, which are not needed when using external current
current transformers, are jumpered by load resistor R40 on the control boards.
If load current monitoring of the phase 2 (not controlled) is desired for Thyro-P 2P,
then an external current transformer and an external voltage transformer must be provided for
this purpose.
CURRENT TRANSFORMER TERMINAL X7.2 TERMINAL X7.1
phase L1 .11(k) .12(l)
phase L2 .21(k) .22(l)
phase L3 .31(k) .32(l)
TAB. 11 CURRENT TRANSFORMER
The following parameters must be checked or adjusted:
HARDWARE-PARAMETER
Current transformer ratio ü:1,
e.g. at 100A/5A transformer is ü=20 UE_I
Type current in A
(Primary current of transformer, e.g. 100A) I_TYP
U_load resistor in V U_load resistor
(Voltage at load resistor)
LIMITATIONS
Ieff max xxxx A IEMA
This is conform to voltage at load resistor at nominal current of transformer.
- THYROP 1
- SAFETY INSTRUCTIONS 4
- TABLE OF CONTENTS 7
- SAFETY REGULATIONS 10
- INTENDED USE 11
- LIABILITY 11
- GUIDELINES 12
- VALIDITY 13
- HANDLING 13
- WARRANTY 13
- INTERNET 14
- COPYRIGHT 14
- 1. INTRODUCTION 15
- 1.3 TYPE DESIGNATION 16
- 2. FUNCTIONS 17
- V / max. 24mA) see ATTENTION 19
- V / max. 12V) 19
- ATTENTION 19
- Set point 20
- Register 20
- 2.3 CONTROL TYPES 21
- 2.3.1 CONTROLLED VALUE 21
- 2.4 INDICATIONS 22
- 2.4.1 LED INDICATIONS 22
- 2.5 MONITORING 23
- 2.5.2. LOAD MONITORING 24
- 2.5.2.2 RELATIVE MONITORING 24
- 2.5.2.3 OVERVIEW MONITORING 27
- („SHORT CIRCUIT MONITORING“) 27
- 2.5.4 FAN MONITORING 28
- 3. OPERATION 29
- Thyro-P Thyro-P 30
- 3.1.4 EASYSTART 31
- 3.1.6 LOAD / SAVE DATA 31
- 3.1.10 LANGUAGES 33
- 3.2 LBA-2 TOOL 33
- 3.2.1 OVERVIEW 34
- 3.2.2 LANGUAGES 35
- 3.2.3 SELECT LOG FILE FOLDER 35
- 3.2.4 CALENDAR NAVIGATION 35
- 3.2.5 TIME AXIS 36
- 3.2.6 VALUE AXES 36
- 3.2.7 VALUES DISPLAY 37
- 3.2.8 EVENT REPORTS 37
- 3.2.9 PDF EXPORT 37
- 3.2.10 EXAMPLE 37
- 3.4 THYRO-TOOL FAMILY 38
- 3.5.1 LBA-2 40
- 3.5.2 THYRO-TOOL FAMILY 40
- 3.6 LBA-2 MENU STRUCTURE 42
- TAB. 6 LBA-2 MENU STRUCTURE 46
- 4. EXTERNAL CONNECTIONS 47
- 4.4 RESET 48
- 4.5 CONTROLLER INHIBIT 48
- 4.6 QUIT 48
- 4.7 SET POINT VALUE INPUTS 49
- 4.8 ASM INPUT 49
- 4.9 dASM INPUT - dASM OUTPUT 49
- 4.10 ANALOG OUTPUTS 49
- 4.11 CURRENT TRANSFORMER 50
- 4.12 VOLTAGE TRANSFORMER 52
- 4.14 SYNCHRONIZATION 54
- X7.1 (-) 56
- X7.2 (+) 56
- 5. INTERFACES 57
- 5.1 RS232 INTERFACE 58
- 5.2 FIBER OPTIC INTERFACE 59
- fiber optic receiver (LLE) X31 60
- 5.3 BUS INTERFACES (OPTIONAL) 62
- FOR COMMISSIONING 63
- OTHER FEATURES 63
- APPROACH FOR dASM APPLICATION 63
- Unit 1 (M) Unit 2 Unit 3 64
- X41 X40 X41 X40 64
- Unit 1 (M) Unit 2 Unit 3 (M) 66
- Controller 1 70
- Controller 2 70
- BASIC CONNECTIONS 71
- 8. CONNECTING DIAGRAMS 73
- Thyro-P 1P 74
- Thyro-P 2P 75
- Thyro-P 3P 76
- Thyro-P 1P...VSC 2 77
- Thyro-P 1P...VSC 3 78
- 9. SPECIAL REMARKS 81
- 9.3 COMMISSIONING 82
- 9.4 SERVICE 82
- 9.5 CHECKLIST 82
- 10. TYPE OVERVIEW 84
- 10.2 TYPE RANGE 500 VOLT 85
- 10.3 TYPE RANGE 690 VOLT 87
- 11. TECHNICAL DATA 88
- Power control P 89
- 12. DIMENSIONAL DRAWINGS 92
- Stat. Alteration Date Name 95
- 2000000282 MB 98
- Vorderansicht / front view 100
- Seitenansicht / side view 100
- Seitenansicht / sideview 101
- 1000 HF 102
- 2 000 000 294 MB 103
- 13. ACCESSORIES AND OPTIONS 105
- CAUTION 106
- and Thyro-P 111
- are trademarks of Advanced 111
Related products and manuals for Power supply units AEG ARE I2
(42 pages)© 2020, manymanuals.com. All rights reserved. | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals