AEG ARE I2 Operations Instructions Page 20
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
18
SET POINT CONTROL CHARACTERISTICS
The set point control characteristic (Fig. 1) of Thyro-P may be easily adapted for the control output
signal of the upstream process controller or automation system. All signals customary on the market
may be used.
The adaption is made by changing the starting and ending points of the control characteristic. Inver-
ted operation (ending value is smaller than the starting value in voltage or current) is also possible.
• Set point 3:
Set point of the superordinate system or PC via RS232 or fiber optic connection (standard) X30, X31
or via the optional bus interface.
• Set point 4:
Set point input (motor potentiometer function) settings as for set point 3 but additionally via LBA-2.
Set point 4 is stored in case of mains failure.
EFFECTIVE TOTAL SET POINT VALUE
The algebraic addition of the results of set point (1,2) to set point 3 and 4 gives the (effective) total
set point value for the set point control characteristic as shown in the following figure.
The prerequisite for a set point to influence the total set point value is that it must be enabled by
the set point Enable Register. Set point 1 and 2 can be linked using the following functions. The
result of this link is called set point (1,2).
Set point link
ADD Set point (1,2) = Set point 1 + Set point 2
IADD Set point (1,2) = Set point 1 - Set point 2
_Pro Set point (1,2) = Set point 1 *
Set point 2 [%]
100%
_IPro Set point (1,2) = Set point 1 * (1 -
Set point 2 [%]
)
100%
VALUE RANGE OF SET POINT (1,2)
For the link result of set point (1,2) the following value range applies:
0
m Set point (1,2) m Set point max (U
max
, I
max
, P
max
).
FIG. 2
TOTAL
SET POINT
Local operating and
display unit LBA-2 or RS232
Bus interface or
Fibre optic interface
Set point 4
Motorpoti function
Set point 3
REMOTE
Set point 1 *
Set point 2 *
Set point
Enable-
Register
ADD
Total
set point
Set point
(1, 2)
ADD
IADD
PRO
IPRO
1
2
4
8
* 0 - 5 Volt
0 - 10 Volt
0(4) - 20 mA
within these limits any linear
control characteristic is possible.
10
13
13
X5.1
M (5V)
M (5V)
ST_A ST_E
ST_A ST_E
X5.1
X5.2
11
X5.2
- THYROP 1
- SAFETY INSTRUCTIONS 4
- TABLE OF CONTENTS 7
- SAFETY REGULATIONS 10
- INTENDED USE 11
- LIABILITY 11
- GUIDELINES 12
- VALIDITY 13
- HANDLING 13
- WARRANTY 13
- INTERNET 14
- COPYRIGHT 14
- 1. INTRODUCTION 15
- 1.3 TYPE DESIGNATION 16
- 2. FUNCTIONS 17
- V / max. 24mA) see ATTENTION 19
- V / max. 12V) 19
- ATTENTION 19
- Set point 20
- Register 20
- 2.3 CONTROL TYPES 21
- 2.3.1 CONTROLLED VALUE 21
- 2.4 INDICATIONS 22
- 2.4.1 LED INDICATIONS 22
- 2.5 MONITORING 23
- 2.5.2. LOAD MONITORING 24
- 2.5.2.2 RELATIVE MONITORING 24
- 2.5.2.3 OVERVIEW MONITORING 27
- („SHORT CIRCUIT MONITORING“) 27
- 2.5.4 FAN MONITORING 28
- 3. OPERATION 29
- Thyro-P Thyro-P 30
- 3.1.4 EASYSTART 31
- 3.1.6 LOAD / SAVE DATA 31
- 3.1.10 LANGUAGES 33
- 3.2 LBA-2 TOOL 33
- 3.2.1 OVERVIEW 34
- 3.2.2 LANGUAGES 35
- 3.2.3 SELECT LOG FILE FOLDER 35
- 3.2.4 CALENDAR NAVIGATION 35
- 3.2.5 TIME AXIS 36
- 3.2.6 VALUE AXES 36
- 3.2.7 VALUES DISPLAY 37
- 3.2.8 EVENT REPORTS 37
- 3.2.9 PDF EXPORT 37
- 3.2.10 EXAMPLE 37
- 3.4 THYRO-TOOL FAMILY 38
- 3.5.1 LBA-2 40
- 3.5.2 THYRO-TOOL FAMILY 40
- 3.6 LBA-2 MENU STRUCTURE 42
- TAB. 6 LBA-2 MENU STRUCTURE 46
- 4. EXTERNAL CONNECTIONS 47
- 4.4 RESET 48
- 4.5 CONTROLLER INHIBIT 48
- 4.6 QUIT 48
- 4.7 SET POINT VALUE INPUTS 49
- 4.8 ASM INPUT 49
- 4.9 dASM INPUT - dASM OUTPUT 49
- 4.10 ANALOG OUTPUTS 49
- 4.11 CURRENT TRANSFORMER 50
- 4.12 VOLTAGE TRANSFORMER 52
- 4.14 SYNCHRONIZATION 54
- X7.1 (-) 56
- X7.2 (+) 56
- 5. INTERFACES 57
- 5.1 RS232 INTERFACE 58
- 5.2 FIBER OPTIC INTERFACE 59
- fiber optic receiver (LLE) X31 60
- 5.3 BUS INTERFACES (OPTIONAL) 62
- FOR COMMISSIONING 63
- OTHER FEATURES 63
- APPROACH FOR dASM APPLICATION 63
- Unit 1 (M) Unit 2 Unit 3 64
- X41 X40 X41 X40 64
- Unit 1 (M) Unit 2 Unit 3 (M) 66
- Controller 1 70
- Controller 2 70
- BASIC CONNECTIONS 71
- 8. CONNECTING DIAGRAMS 73
- Thyro-P 1P 74
- Thyro-P 2P 75
- Thyro-P 3P 76
- Thyro-P 1P...VSC 2 77
- Thyro-P 1P...VSC 3 78
- 9. SPECIAL REMARKS 81
- 9.3 COMMISSIONING 82
- 9.4 SERVICE 82
- 9.5 CHECKLIST 82
- 10. TYPE OVERVIEW 84
- 10.2 TYPE RANGE 500 VOLT 85
- 10.3 TYPE RANGE 690 VOLT 87
- 11. TECHNICAL DATA 88
- Power control P 89
- 12. DIMENSIONAL DRAWINGS 92
- Stat. Alteration Date Name 95
- 2000000282 MB 98
- Vorderansicht / front view 100
- Seitenansicht / side view 100
- Seitenansicht / sideview 101
- 1000 HF 102
- 2 000 000 294 MB 103
- 13. ACCESSORIES AND OPTIONS 105
- CAUTION 106
- and Thyro-P 111
- are trademarks of Advanced 111
Related products and manuals for Power supply units AEG ARE I2
(42 pages)© 2020, manymanuals.com. All rights reserved. | 1.779 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals