USER MANUALEN User ManualDishwasherFFB93706PM
5.2 Information for testinstitutesFor all the necessary information for testperformance, send an email to:[email protected] dow
6.3 How to change a settingwith multiple valuesSaved settings remain valid until youchange them again.1. Press .The display shows the option list.2.
7. OPTIONSDesired options must beactivated every time beforeyou start a programme.It is not possible to activateor deactivate options while aprogramme
automatically activated in next cycles.This configuration can be changed at anytime.Every time ECO 50° isactivated, XtraDry is off andneeds to be chos
right level of the water softener to assuregood washing results.Water hardnessGerman de-grees (°dH)French degrees(°fH)mmol/l Clarke de-greesWater soft
6. Turn the cap of the salt containerclockwise to close the salt container.CAUTION!Water and salt can come outof the salt container whenyou fill it. A
• If the display shows the saltrefilling message, fill the saltcontainer.• If the rinse aid empty message isshown, fill the rinse aid dispenser.3. Loa
to confirm. Close theappliance door.Cancelling a runningprogramme1. Open the appliance door.2. Press and hold for about 3seconds. The display shows
• Select the program according to thetype of load and degree of soil. Withthe ECO program you have the mostefficient use of water and energyconsumptio
At the end of the programwater can still remain on thesides and on the door of theappliance.11. CARE AND CLEANINGWARNING!Before maintenance,deactivate
CONTENTS1. SAFETY INFORMATION...22. SAFETY INSTRUCTIONS...
7. Reassemble the filters (B) and (C).8. Put back the filter (B) in the flat filter(A). Turn it clockwise until it locks.CAUTION!An incorrect position
11.4 External cleaning• Clean the appliance with a moist softcloth.• Only use neutral detergents.• Do not use abrasive products,abrasive cleaning pads
Problem and alarm code Possible cause and solutionThe appliance does notdrain the water.The display shows .• Make sure that the sink spigot is not cl
Problem Possible cause and solutionPoor drying results. • Tableware was left for too long inside the closed ap-pliance.• There is no rinse aid or the
Problem Possible cause and solutionOdours inside the appliance. • Refer to "Internal cleaning".• Start the Machine Care programme with a des
14. ENVIRONMENTAL CONCERNSRecycle materials with the symbol .Put the packaging in relevant containersto recycle it. Help protect theenvironment and h
www.aeg.com26
ENGLISH 27
www.aeg.com/shop117873530-A-042018
manufacturer is not responsible for any injuries ordamages that are the result of incorrect installation orusage. Always keep the instructions in a sa
• If the supply cord is damaged, it must be replaced bythe manufacturer, its Authorised Service Centre orsimilarly qualified persons in order to avoid
fuse, use only a 13 A ASTA (BS 1362)fuse.2.3 Water connection• Do not cause damage to the waterhoses.• Before connection to new pipes,pipes not used f
3. PRODUCT DESCRIPTION675111081213 342191Worktop2Top spray arm3Upper spray arm4Lower spray arm5Filters6Rating plate7Salt container8Air vent9Rinse aid
4. CONTROL PANEL132 4 5 6789101On/off button2Programs touch button3Navigation touch button (up)4Display5Delay touch button6MyFavourite touch button7OK
5. PROGRAMMESProgramme Degree of soilType of loadProgramme phases OptionsECO 50° 1)• Normal soil• Crockery and cut-lery• Prewash• Wash 50 °C• Rinses•
Programme Degree of soilType of loadProgramme phases OptionsMachine Care 10)• No load • Self-cleaning 1) This programme offers the most efficient use
Comments to this Manuals