AEG FFB63700PM User Manual

USER MANUALEN User ManualDishwasherFFB63700PM

6. SETTINGS6.1 Programme selectionmode and user modeWhen the appliance is in programmeselection mode it is possible to set aprogramme and to enter use

German de-grees (°dH)French degrees(°fH)mmol/l Clarke de-greesWater softener lev-el<4 <7 <0.7 < 51 2)1) Factory setting.2) Do not use salt

6.5 AirDryAirDry improves the drying results withless energy consumption.During the drying phase, thedoor opens automaticallyand remains ajar.CAUTION!

7.1 XtraDryActivate this option to boost the dryingperformance.XtraDry is a permanent option for allprogrammes other than . It isautomatically activa

3. Fill the salt container with dishwashersalt (until it is full).4. Carefully shake the funnel by itshandle to get the last granulesinside.5. Remove

• If the salt indicator is on, fill thesalt container.• If the rinse aid indicator is on, fillthe rinse aid dispenser.3. Load the baskets.4. Add the d

Cancelling a programmePress and hold simultaneously Delay and Option until the appliance is inprogramme selection mode.Make sure that there is deterge

1. Set the highest level of the watersoftener.2. Make sure that the salt and rinse aidcontainers are full.3. Start the shortest programme with arinsin

CBA1. Turn the filter (B) counterclockwiseand remove it.2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A).4. Wash the filters.

11.2 Cleaning the upper sprayarmWe recommend to clean regularly theupper spray arm to avoid soil to clog theholes.Clogged holes can cause unsatisfacto

CONTENTS1. SAFETY INFORMATION...22. SAFETY INSTRUCTIONS...

12. TROUBLESHOOTINGWARNING!Improper repair of theappliance may pose adanger to the safety of theuser. Any repairs must beperformed by qualifiedpersonn

Problem and alarm code Possible cause and solutionThe programme lasts toolong.• If the delay start option is set, cancel the delay setting orwait for

Problem Possible cause and solutionPoor drying results. • Tableware has been left for too long inside a closedappliance.• There is no rinse aid or the

Problem Possible cause and solutionLimescale deposits on the ta-bleware, on the tub and onthe inside of the door.• The level of salt is low, check the

14. ELECTROLUX / AEG MAJOR APPLIANCES -WARRANTY CONDITIONSFor domestic use only.Not for commercial or industrial use.Any alteration or modification of

appliances from an authorisedElectrolux Dealer or Distributor andonly where the appliance has beenretained for use in the Republic ofSouth Africa.10.

appliances marked with the symbol with the household waste. Return theproduct to your local recycling facility orcontact your municipal office.*www.ae

ENGLISH 27

www.aeg.com/shop117874280-A-512017

manufacturer is not responsible for any injuries ordamages that are the result of incorrect installation orusage. Always keep the instructions in a sa

• If the supply cord is damaged, it must be replaced bythe manufacturer, its Authorised Service Centre orsimilarly qualified persons in order to avoid

fuse, use only a 13 A ASTA (BS 1362)fuse.2.3 Water connection• Do not cause damage to the waterhoses.• Before connection to new pipes,pipes not used f

3. PRODUCT DESCRIPTION65911 10 7812 13 34211Worktop2Top spray arm3Upper spray arm4Lower spray arm5Filters6Rating plate7Salt container8Air vent9Rinse a

4. CONTROL PANEL12 4 568371On/off button2Program button3Programme indicators4Display5Delay button6Option button7Indicators8Start button4.1 IndicatorsI

5. PROGRAMMESProgramme Degree of soilType of loadProgramme phases Options 1)• Normal soil• Crockery andcutlery• Prewash• Wash 50 °C• Rinses• Dry• Extr

Programme Degree of soilType of loadProgramme phases Options 7)• Normal soil• Crockery andcutlery• Prewash• Wash 50 °C• Rinses• Dry• XtraDry1) This pr