L 75672 FL EN User manual
ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsExtra Stil95° - ColdWhite and colouredcotton with normalsoil.max. 7 kgStop
ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsGordijnen40° - ColdSet this programmeto wash curtains. Itadds automatically
6) Set this programme to have a good washing results and decrease the energyconsumption. The time of the washing programme is extended.7) Standard pro
8. USING THE APPLIANCE1.Open the water tap.2.Connect the mains plug to the mainssocket.3.Press button 1 to activate the ap-pliance.4.Put the laundry i
This is the maximum level for the quantity of liquid additives.The compartment for the stain remover.Put the product in the compartment and set the st
5.Measure out the detergent and thefabric conditioner.6.Carefully close the detergent dis-penser. Make sure that the flapdoes not cause a blockage whe
To open the appliance door:1.Press button 4 . The door locksymbol in the display goes off.2.Open the appliance door.3.Close the appliance door and pre
10. HELPFUL HINTS AND TIPS10.1 The laundry load• Divide the laundry in: white, coloured,synthetics, delicates and wool.• Obey the washing instructions
Water hardness tableLevel TypeWater hardness°dH °T.H. mmol/l Clarke1 soft 0-7 0-15 0-1.5 0-92 medium 8-14 16-25 1.6-2.5 10-163 hard 15-21 26-37 2.6-3.
11.6 Detergent dispenserTo clean the dispenser:121.Press the lever.2.Pull the dispenser out.3.Remove the top part of the liquidadditive compartment.4.
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNICAL I
To clean the drain pump:1.Open the drain pump door.2.Pull the flap out to remove it.3.Put a container below the recess ofthe drain pump to collect the
129.Clean the filter under the water tapand put it back in the pump into thespecial guides.10.Make sure that you tighten correctlythe filter to preven
Put the drainage duct back and close thedrain pump flap.When you drain the water with the emer-gency drain procedure, you must acti-vate again the dra
Problem Possible cause Possible solutionThe appliancedoes not drain thewater.The water drain hose isdamaged.Make sure that the water drainhose has no
Problem Possible cause Possible solution Leakages from the drainpump.Make sure that the drain pumpfilter is tight. The water drain hose isdamaged.Ma
We recommend that you write theinformation here:Model(MOD.)...Product number(PNC)...Serial number(S.N.)...
5.Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6.Put one of the polystyrene packag-ing elements on t
10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th
• The appliance must be level and sta-ble.CAUTION!Do not put cardboard, wood orequivalent materials below theappliance feet to adjust the level.13.4 T
Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t
1. SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environ
Without the plastic hose guide.• To a sink spigot.Refer to the illustration. Put the drainhose in the spigot and tighten it with aclip. Make sure that
ENGLISH 31
www.aeg.com/shop132924710-A-172012
• Do not install and connect a damagedappliance.• Make sure to remove all packagingand transport bolts.• Make sure that the mains plug is dis-connecte
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1600 rpm1
4. ACCESSORIES1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra
D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th
Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11
Comments to this Manuals