AEG L75480WD User Manual

L 75480 WD EN User manual

D • The programme time (washing and/or drying phase)When the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you pr

5.10 Spin button 9Press this button to:• Decrease the maximum speed of thespin phase when you set a pro-gramme.The display shows only the spinspeeds a

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsSynthetics60° - ColdSynthetic or mixedfabric items with nor-mal level of s

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsDRYING PROGRAMMESWool dry Wool itemsmax. 1 kgTimed drying onlySynthetics d

6.1 Programmes for automatic dryingLevel of dryness Type of fabric LoadExtra dryFor towelling materialsCotton and linen(bathrobes, bath towels,etc)up

7. CONSUMPTION VALUESProgramme Energy con-sumption(KWh)Water con-sumption(litres)Programmeduration(minutes)Cottons 60° 1.60 72For the du-ration of the

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a

Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge

5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The drain pump can operate fora short time when the appliancefills water.The

•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving function automatically deacti-vates th

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

Set time value• Each time you press this button thetime value increases by 5 minutes.• After some seconds the time value onthe display changes: the ap

The set dryness level sym-bol stays on.The others level symbolsgo off.The door locked symbolcomes on.The display shows the new time valueeach minute.T

To remove the fluff inside the drum,set a special programme:• Empty the drum.• Clean the drum, the gasket and thedoor with a wet cloth.• Set the rinse

• mmol/l (millimol for each litre - inter-national unit for the hardness of wa-ter).• Clarke degrees.Water hardness tableLevel TypeWater hardness°dH °

13. CARE AND CLEANINGWARNING!Disconnect the appliance from the mainssupply before you clean it.13.1 DescalingThe water we use contains limescale. If i

13.6 Detergent dispenserTo clean the dispenser:121.Press the lever.2.Pull the dispenser out.3.Remove the top part of the liquidadditive compartment.4.

To clean the drain pump:1.Open the drain pump door.2.Pull the flap out to remove it.3.Put a container below the recess ofthe drain pump to collect the

129.Clean the filter under the water tapand put it back in the pump into thespecial guides.10.Make sure that you tighten correctlythe filter to preven

Put the drainage duct back and close thedrain pump flap.When you drain the water with the emer-gency drain procedure, you must acti-vate again the dra

Problem Possible cause Possible solutionThe appliancedoes not drain thewater.The water drain hose isdamaged.Make sure that the water drainhose has no

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

Problem Possible cause Possible solution Leakages from the drainpump.Make sure that the drain pumpfilter is tight. The water drain hose isdamaged.Ma

Problem Possible cause Possible solution You have set a wrongdryness level or dryingtime.Set additional drying time.There is a bigquantity of fluff i

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

16. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

38www.aeg.com

ENGLISH 39

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

www.aeg.com/shop132926382-A-422013

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

• Disconnect the appliance from themains supply.• Cut off the mains cable and discard it.• Remove the door catch to preventchildren and pets to get cl

4. PRODUCT DESCRIPTION1 2 3 8956741011121Worktop2Detergent dispenser3Control panel4Door handle5Rating plate6Drain pump7Feet for the appliance level8Wa

4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra