AEG L76485HFL User Manual

L 76485 HFL EN User manual

ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsKoch/Bunt +Vorwâsche95° - ColdWhite and colouredcotton with heavysoil.max.

ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsGardinen40° - ColdSet this programmeto wash curtains. Itadds automaticallyt

7) Set this programme to have a good washing results and decrease the energyconsumption. The time of the washing programme is extended.8) Standard pro

Off Mode (W) Left On Mode (W)The values of power consumption of the «Off-mode » and «Left-on mode» arein compliance with the EU Commision regulation 2

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.8.2 Filling the detergent andad

Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge

5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The drain pump can operate fora short time when the appliancefills water.The

•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving function automatically deacti-vates th

• To help the environment, do not usemore than the correct quantity of de-tergent.• Obey the instructions that you find onthe on packaging of these pr

10.3 External cleaningClean the appliance only with soap andwarm water. Fully dry all the surfaces.CAUTION!Do not use alcohol, solvents orchemical pro

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNIC

5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.10.7 Drain pumpRegularly examine the drainpump and make sure that it i

125.When the container is full of water,put the drainage duct back againand empty the container. Do steps 4and 5 again and again until no morewater fl

1.Close the cold water tap.2.Remove the cold water inlet hosefrom the cold water tap.3.Clean the filter in the cold inlet hosewith a stiff brush.4.Rem

11. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water taps.• Contact the service centre.

Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

• Connect the water inlet hoses to thecold and hot water taps with 3/4thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an

1. SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environ

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

13. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

www.aeg.com/shop132921250-A-212012

• Do not install and connect a damagedappliance.• Make sure to remove all packagingand transport bolts.• Make sure that the mains plug is dis-connecte

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterHot water2)Maximum load Cotton 8 kgSpin speed Maximu

1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit bolts.3Cold an

5.2 Programme knob 2Turn this knob to set a programme. Therelated programme indicator comes on.5.3 Display 3A B C DThe display shows:A • The maximum t

D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th

ter when the programme is comple-ted.Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the de