L 56006 SL EN User manual
6. PROGRAMMESProgrammeTemperature rangeType of load and soilMaximum load, Maximum spinΧлопох95° C - ColdWhite cotton and coloured cotton (normal soila
2) Set this programme to have a good washing results and decrease the energyconsumption. The time of the washing programme is extended.Programme optio
Programmes Load(Kg)Energyconsump-tion(kWh)Water con-sumption(litre)Programmeduration(minutes)Χлопох Эко 60 °C1)6 0.76 49 169Χлопох 40 °C 6 0.75 56 145
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a
Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge
5.Press button 4 to start the pro-gramme. The indicator of button 4is on with red colour.The drain pump can operate fora short time when the appliance
When you activate the applianceagain, the display show the endof the last set programme. Turnthe programme knob to set anew cycle.• Remove the laundry
• If you use liquid detergents, do not setthe prewash phase.• If your appliance has not the deter-gent dispenser with the flap device,add the liquid d
11.4 Door sealRegularly examine the seal and removeall objects from the inner part.11.5 DrumRegularly examine the drum to preventlimescale and rust pa
11.7 Drain pumpRegularly examine the drainpump and make sure that it isclean.Clean the pump if:• The appliance does not drain the wa-ter.• The drum ca
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Clean the filter under the water tapand put
4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur
• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.WARNING!Deactivate the appliance beforeyou do the chec
Problem Possible cause Possible solutionThe programmedoes not start.The mains plug is notconnected in the mainssocket.Put in the mains plug. Blow out
After the check, activate the appliance.The programme continues from thepoint of interruption.If the problem occurs again, contact theservice centre.I
5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put
10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th
13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
Without the plastic hose guide.• To a sink spigot.Refer to the illustration. Put the drainhose in the spigot and tighten it with aclip. Make sure that
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
30www.aeg.com
ENGLISH 31
www.aeg.com/shop132913750-A-132013
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 6 kgSpin speed Maximum 1000 rpm1
4.1 Accessories1 24 31SpannerTo remove the transit bolts.2Plastic hose guideTo connect the drain hose on theedge of a sink.3Plastic capsTo close the h
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra
5.4 Start/Pause button 4Press button 4 to start or interrupt aprogramme.5.5 Delay start button 5Press button 5 to delay the start of aprogramme from 3
Comments to this Manuals