AEG FSE83710P User Manual

USER MANUALEN User ManualDishwasherFSE83710P

How to set the programmeselection modeThe appliance is in programme selectionmode when the display shows theprogramme number P1.After activation, the

2. Press .• The indicators , , , and are off.• The indicator still flashes.• The display shows the currentsetting: e.g. = level 5.3. Press

There is also an acoustic signal thatsounds when the programme iscompleted. By default this acousticsignal is deactivated but it is possible toactivat

How to deactivate AirDryThe appliance must be in programmeselection mode.1. To enter the user mode, press andhold simultaneously and untilthe indi

7.3 ExtraHygieneThis option provides better hygieneresults by keeping the temperature at 70°C for at least 10 minutes during the lastrinsing phase.How

8.2 How to fill the rinse aiddispenserABCCAUTION!Only use rinse aidspecifically designed fordishwashers.1. Open the lid (C).2. Fill the dispenser (B)

detergent on the inner part of theappliance door.4. Close the lid. Make sure that the lidlocks into position.9.2 Setting and starting aprogrammeThe Au

10. HINTS AND TIPS10.1 GeneralThe following hints will ensure optimalcleaning and drying results in daily useand also help to protect theenvironment.•

• Make sure that the spray arms canmove freely before you start aprogramme.10.5 Before starting aprogrammeMake sure that:• The filters are clean and c

5. Make sure that there are no residuesof food or soil in or around the edgeof the sump.6. Put back in place the flat filter (A).Make sure that it is

CONTENTS1. SAFETY INFORMATION...22. SAFETY INSTRUCTIONS...

11.3 External cleaning• Clean the appliance with a moist softcloth.• Only use neutral detergents.• Do not use abrasive products,abrasive cleaning pads

Problem and alarm code Possible cause and solutionThe appliance does not fillwith water.The display shows .• Make sure that the water tap is open.• M

Refer to "Before first use", "Daily use", or "Hints andtips" for other possiblecauses.Once you have checked the applianc

Problem Possible cause and solutionTraces of rust on cutlery. • There is too much salt in the water used for washing.Refer to "The water softener

Water supplyCold water or hot water 2)max 60 °CCapacity Place settings 15Power consumption Left-on mode (W) 5.0Power consumption Off-mode (W) 0.101) R

ENGLISH 25

www.aeg.com26

ENGLISH 27

www.aeg.com/shop117883340-A-112017

manufacturer is not responsible for any injuries ordamages that are the result of incorrect installation orusage. Always keep the instructions in a sa

• Do not leave the appliance with the open doorunattended to avoid stepping accidentally onto it.• Before any maintenance operation, deactivate theapp

• Ensure that there are no visible waterleaks during and after the first use ofthe appliance.• The water inlet hose has a safety valveand a sheath wit

3. PRODUCT DESCRIPTION5410 9 6711 12 2318 1Top spray arm2Upper spray arm3Lower spray arm4Filters5Rating plate6Salt container7Air vent8Rinse aid dispen

When AirDry is activatedduring the drying phase, theprojection on the floor maynot be completely visible. Tocheck the remaining time ofthe running pro

Programme Degree of soilType of loadProgramme phases OptionsP2 2)• All• Crockery, cut-lery, pots andpans• Prewash• Wash from 45 °C to 70°C• Rinses• Dr

5.1 Consumption valuesProgramme 1)Water(l)Energy(kWh)Duration(min)P1 11 0.857 232P2 7 - 14 0.6 - 1.6 40 - 170P5 14 - 16 1.2 - 1.5 160 - 180P3 12.5-14.