AEG L76489FL User Manual

L 76489 FLL 76689 FLEN User manual

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsKatoen + Voor-was95° - ColdWhite and colouredcotton with heavysoil.max. 8

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCentrifugeren/Pompen3)All fabricsThe maximum loadof the laundry is rela-te

STEAM PROGRAMMESProgramme1)Type of load Max. loadOpfrissenThis cycle removes odoursfrom the laundry.Steam does not re-move animal odours.Cotton and sy

Programmes Load(kg)Energyconsump-tion(kWh)Watercon-sump-tion (li-tre)Approxi-matepro-grammeduration(mi-nutes)Remain-ingmois-ture(%)1)L 76489FLRemain-i

5.Use the correct quantity of deter-gent and additives.6.Set and start the correct programmefor the type of laundry and soil.9.1 Loading the laundry1.

Flap for powder or liquid detergentTurn it (up or down) in the correct position to use powder or liq-uid detergent.Always obey the instructions that y

9.3 Setting and starting aprogramme1.Turn the programme knob. The rela-ted programme indicator comes on.2.The indicator of button 4 flasheswith red co

If the temperature and level ofthe water in the drum are toohigh, the door lock symbol stayson and you cannot open thedoor. To open the door do theste

• Wash with a special detergent heavysoil stains.• Be careful with the curtains. Removethe hooks or put the curtains in awashing bag or pillowcase.• D

12.1 DescalingThe water we use contains limescale. If itbecomes necessary, use a water softenerto remove limescales.Use a special product made for was

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNIC

3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put back the dispe

3.Put a container below the recess ofthe drain pump to collect the waterthat flows out.4.Press the two levers and pull for-ward the drainage duct to l

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

13. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T

Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

1. SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environ

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

15. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

www.aeg.com/shop132921010-A-202012

• Do not install and connect a damagedappliance.• Make sure to remove all packagingand transport bolts.• Make sure that the mains plug is dis-connecte

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 8 kgSpin speed Maximum 1400 rpm

4. ACCESSORIES1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th

Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11