AEG L61470BI User Manual

LAVAMAT 61271 BILAVAMAT 61470 BIEN User manual

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsCottons + Prewash3)95° - ColdMax. load 7 kg - Reduced load

ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsSpinMax. load 7 kgSeparate spin for hand washed cotton gar

1) Stain option can be selected only at the temperature of 40°C or higher.2) If you select the Super Quick option by pressing button 6, we recommend t

Off Mode (W) Left On Mode (W)The information given in the charts above are in compliance with the EU Com-mision regulation 2015/2010 implementing dire

The detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent for prewash, soak and stain remover be

This option is not available witha temperature lower than 40°C.If you wish to perform a programme withthe stain option, pour stain remover intocompart

• Press the button 8 to set the washingmachine to PAUSE;• Press the button 9 once until the dis-play shows the symbol ’;• Press the button 8 again to

10. HELPFUL HINTS AND TIPS10.1 The laundry load• Divide the laundry in: white, coloured,synthetics, delicates and wool.• Obey the washing instructions

Water hardness tableLevel TypeWater hardness°dH °T.H. mmol/l Clarke1 soft 0-7 0-15 0-1.5 0-92 medium 8-14 16-25 1.6-2.5 10-163 hard 15-21 26-37 2.6-3.

11.5 Detergent dispenserTo clean the dispenser:MAX121.Press the lever.2.Pull the dispenser out.MAX3.Remove the top part of the liquidadditive compartm

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

AB3.Place a container close to the pumpto collect any spillage.4.Release the emergency emptyinghose (B), place it in the containerand remove its cap c

8.Put the cap back on the emergencyemptying hose and place the latterback in its seat.9.Replace the filter into the pump byinserting it correctly into

45°20°6.Install again the inlet hose. Makesure that the couplings are tight toprevent leakages.7.Open the water tap.11.8 Emergency emptying outIf the

Problem Possible cause/SolutionThe washing machinedoes not start:The door has not been closed. • Close the door firmly.The plug is not properly insert

Problem Possible cause/SolutionThere is water on thefloor:Too much detergent or unsuitable detergent (cre-ates too much foam) has been used.• Reduce t

Problem Possible cause/SolutionSpinning starts late orthe machine does notspin:The electronic unbalance detection device has cut inbecause the laundry

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

13.3 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t

• If the end of the drain hose is this (seethe drawing), you can push it directlyinto the stand pipe.Without the plastic hose guide.• To a sink spigot

13.5 In the interest of the environment• Connect the appliance to the FOULsystem for the drain water. The sew-age works keeps the drain water forthe t

Preparation and assembly of the door• The machine is originally pre-arrangedfor the assembly of a door openingfrom right to left (Fig. 2).Fig. 2Ø 35 m

BA• Mounting the doorFix the hinges to the appliance bymeans of the M5x15 screws . The hing-es can be adjusted to compensate forpossible uneven thickn

ENGLISH 35

www.aeg.com/shop132927081-A-482012

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

mains plug, use a 13 amp ASTA (BS1362) fuse.•This appliance complies with theE.E.C. Directives.Water connection• Make sure not to cause damage to thew

Level of protection against ingress of solid parti-cles and moisture ensured by the protective cover,except where the low voltage equipment has noprot

4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

5.1 DisplayThe display shows the following informa-tion:Duration of the set programmeWhen you set a programme, the display shows the duration inhours

5.2 Indicator pilot lightsABCAfter you have pressed the button 8, theWASHING light (A) comes on.The machine is operating.The DOOR light (B) indicates