AEG L 60460 FL User Manual

L 60260 FLL 60460 FLL 60660 FLEN User manual

6. PROGRAMMESProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCottons95° - ColdWhite and colouredcotton with normalsoil.max

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsDrain All fabricsThe maximum loadof the laundry is rela-ted to the type of

programmes in terms of combined energy and water consumption for washing normallysoiled cotton laundry.Set this programme to have a good washing resul

Pro-grammesLoad(kg)Energycon-sump-tion(kWh)Watercon-sump-tion (li-tre)Ap-proxi-matepro-gramme dura-tion(mi-nutes)Re-main-ingmois-ture(%)1)L60260FLRe-m

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a

Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge

5.Press button 4 to start the pro-gramme. The indicator of button 4is on with red colour.The drain pump can operate fora short time when the appliance

• The door lock symbol goes off.•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving functi

• Do not mix different types of deter-gents.• To help the environment, do not usemore than the correct quantity of de-tergent.• Obey the instructions

• Set the hottest cotton wash pro-gramme• Use a correct quantity of powder de-tergent with biological properties.After each wash, keep the door open f

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.11.7 Drain pumpRegularly examine the drainpump and make sure that it i

6.Remove fluff and objects from thepump.7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Cle

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

12. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe spin phasedoes not operate.The spin phase is off. Set the spin programme. The filter of the drainpump is

Problem Possible cause Possible solution You did not remove thestubborn stains beforeyou wash the laundry.Use special products to removethe stubborn

4.Remove the internal film.5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindt

9.Remove the power supply cable andthe drain hose from the hose hold-ers.10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out

13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc

13.4 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t

• If the end of the drain hose is this (seethe drawing), you can push it directlyinto the stand pipe.Without the plastic hose guide.• To a sink spigot

13.6 In the interest of the environment• Connect the appliance to the FOULsystem for the drain water. The sew-age works keeps the drain water forthe t

ENGLISH 33

34www.aeg.com

ENGLISH 35

www.aeg.com/shop132932652-A-022013

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

mains plug, use a 13 amp ASTA (BS1362) fuse.•This appliance complies with theE.E.C. Directives.Water connection• Make sure not to cause damage to thew

Level of protection against ingress of solid particlesand moisture ensured by the protective cover, ex-cept where the low voltage equipment has no pro

4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

5.4 Start/Pause button 4Press button 4 to start or interrupt aprogramme.5.5 Delay start button 5Press button 5 to delay the start of aprogramme from 3