AEG ZX6640SI User Manual download pdf (Page 14)

If the appliance is foreseen to operate with a type of gas different

from the suitable supply gas, proceed as follows: change the

injectors, adjust the minimum flow of the burners, change the

push-on connector.

In order to change the work-top injectors, it is necessary to act as

follows: remove the grids, remove burners and flame-spreaders

(see fig.A), change the injector (see fig.B) and replace it with

another one suitable for the new type of gas (see table D). Re-

assemble everything in the opposite direction, paying attention to

place the flame-spreader in the right way on the burner.

To change the oven injector, it is necessary to act as follows: open

the oven door, remove the lower side of the oven (see fig.C),

unscrew screw C and disassemble the oven burner (see fig.D).

Change the injector (see fig.E) and replace it with another one

suitable for the new gas type (see table D).

Re-assemble everything in the opposite direction, paying attention

to place the burner in the right way on its rear slot.

Fig. 41

GAS ADJUSTMENT

Fig. 39

HOB

4 BURNERS 3 BURNERS

1 EL. PLATE

E = Ø145mm

1000 ÷ 1500W

To change the grill injector, it is necessary to act as follows: open

the oven door, unscrew screw C and disassemble the grill burner

(see fig.F). Change the injector (see fig.G) and replace it with

another one suitable for the new gas type (see table D).

Re-assemble everything in the opposite direction, paying attention

to place the burner in the right way on its rear slot.

Fig. 42

Fig. 43 Fig. 44

MINIMUM FLOW ADJUSTMENT FOR WORK-TOP TAPS

In order to adjust the minimum, act as follows: switch the burner

on, and turn the knob towards the minimum flow position

Remove the knob from the tap, introduce a little screwdriver in the

tap rod (fig. 43).

Attention: in taps with security valve, the minimum adjusting screw

“Z” is placed outside the rod tap (fig. 44).

Fig. 45 Fig. 46

Unscrew the adjusting screw in order to increase the flow or screw

it to decrease the flow.

The right adjustment is obtained when the flame has a length of

about 3 or 4 mm.

For butane/propane gas, the adjusting screw must be tight screwed.

Make sure that the flame does not go out passing quickly from

the max. flow

to the minimum flow and viceversa .

Assemble the knob again.

MINIMUM FLOW ADJUSTMENT FOR OVEN THERMOSTAT

In order to adjust the minimum, act as follows: switch the burner

on turning the knob to the maximum position.

Remove the knob and unscrew of some turns the by-pass screw

(fig. 45).

Assemble the knob and let the oven warm up for 15 minutes; after

that turn the knob to the minimum position.

After having removed the knob once again, making sure that the

thermostat rod has not been moved, screw slightly the above

mentioned by-pass screw, to obtain a flame of 3 or 4 mm of length.

For butane/propane gas, the adjusting screw must be tight screwed.

Make sure that the flame does not extinguish passing quickly from

the maximum flow to the minimum flow, and closing and opening

the oven door (the oven door must be closed softly).

Attention: for taps with safety device, the minimum adjusting screw

“T” is on the outside of the tap rod (fig. 46).

TAB. D GENERAL INJECTORS TABLE

Kind of gas mbar Nozzle Burners Potenza Watt Consumo

N. Posizione-tipo max. min. max.

118 A-Rapide 3000 750 286 l/h

NATURAL 20 97 B,C-Semi rapide 1750 440 167 l/h

72 D-Auxiliary 1000 300 95 l/h

140 A-Triple crown 3500 1500 317 l/h

115 Oven 3100 1000 296 l/h

100 Grill 2100 200 l/h

G.P.L. 30 85 A-Rapide 3000 750 219 g/h

BUTANE 28 65 B,C-Semi rapide 1750 440 128 g/h

PROPANE 37 50 D-Auxiliary 1000 300 73 g/h

94 A-Triple crown 3300 1500 255 g/h

82 Oven 3100 1000 226 g/h

73 Grill 2100 153 g/h

1 2 ... 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

AEG ZX6640SI User Manual Page 14

Comments to this Manuals

Related products and manuals for Kitchen & houseware accessories AEG ZX6640SI