AEG 69802G-M User Manual

AUS ERFAHRUNG GUT69802 GGas HobOperating InstructionsGBPERFECT IN FORM AND FUNCTION

10Guarantee ConditionsStandard guarantee conditionsWe, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any p

11Burner Dia. Tap By-pass1/100 mmAuxiliary 28Semi-rapid 32Rapid 40Aeration adjustment noneOVERALL DIMENSIONS Width: 580 mm.Depth: 510 mm.Height: 88 m

12BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1

13InstallationIMPORTANTThis hob must be installed by qualified personnel to the relevant BritishStandards.Any gas installation must be carried out by

14A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment isfixed s

15550470580510Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard ordrawerIf the hob is to be insta

16Building over a kitchen unit with doorProper arrangements must be taken indesigning the furniture unit, in order toavoid any contact with the bottom

17Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

18Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity

19Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

2Important Safety InformationYou MUST read these warnings carefully before installing or using thehob. If you need assistance, contact our Customer Ca

20A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale andadjust zero if necessary.— Test leads fro

21Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

22CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flamesetting. To do this, follow the procedure below.1)

23Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gas but can beconverted for use with buta

35686-0001 01/04AEG Hausgeräte GmbHPostfach 1036D-90327 Nürnberghttp://www.aeg.hausgeraete.de© Electrolux plc 2003Grafiche MDM - For

3z Do not use this hob if it is in contact with water. Do not operate the hob withwet hands.z Ensure the control knobs are in the ‘OFF’ position when

4ContentsImportant Safety Information ... 2Instructions for the User ...

51. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burn

6HOB BURNERSTo light a burner, turn the relevant control knob anticlockwise to the maximumposition, then push it down to ignite the burner. Upon, igni

7Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is st

8Something Not Working?If the hob is not working correctly, please carry out the following checks beforecontacting your local AEG Service Force Centre

9Service and Spare PartsWhen you contact the Service Centre, they will need the following information:1. Your name, address and post code.2. Your tele