L 76685 FL EN User manual
ProgrammeTemperatureType of loadmax. weight ofloadCycle description Functions Cottons + Pre-wash95° - ColdWhite and colouredcotton with heavysoil.max.
ProgrammeTemperatureType of loadmax. weight ofloadCycle description Functions RinseHand washingitems.RinsesLong spinSPIN REDUC-TIONRINSE HOLDEXTRA RIN
STEAM PROGRAMMESProgramme1)Type of load Max. load Steam RefreshThis cycle removes odoursfrom the laundry.Steam does not re-move animal odours.Cotton a
Programmes Load(Kg)Energy con-sumption(kWh)Water con-sumption (li-tre)Approxi-mate pro-grammeduration(minutes)Remainingmoisture(%)1)Delicates 40°C4 0.
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.7.2 Filling the detergent andad
Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge
5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The drain pump can operate fora short time when the appliancefills water.The
• The door lock symbol goes off.•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving functi
• Do not mix different types of deter-gents.• To help the environment, do not usemore than the correct quantity of de-tergent.• Obey the instructions
• Set the hottest cotton wash pro-gramme• Use a correct quantity of powder de-tergent with biological properties.After each wash, keep the door open f
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNIC
5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.9.7 Drain pumpRegularly examine the drainpump and make sure that it is
125.When the container is full of water,put the drainage duct back againand empty the container. Do steps 4and 5 again and again until no morewater fl
To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif
10. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta
Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T
Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai
2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from
127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f
WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
1. SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environ
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
12. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a
www.aeg.com/shop132921260-A-212012
• Do not install and connect a damagedappliance.• Make sure to remove all packagingand transport bolts.• Make sure that the mains plug is dis-connecte
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 8 kgSpin speed Maximum 1600 rpm1
1 2 3451SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit bolts.3Anti-
9Spin reduction button10Temperature button4.1 On Off button 1Press this button to activate or deacti-vate the appliance. A tune sounds whenthe applian
Delay startD • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start
Spin phase is off.'Rinse Hold' function ison.4.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water4.11
Comments to this Manuals