L 85275 XFL EN User manualwww.devicemanuals.eu
If you make a wrong selection the message Err indicates that the selec-tion is not possible.JThe time save symbol comes on when you set one of theprog
recommend that you use this functionwhen you have laundry with a high lev-el of soil.The set of this function increasesthe programme duration.5.9 Spin
6. PROGRAMMESProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsCottons95° - ColdWhite and coloured cottonwith heavy level
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsAnti-Allergy60°White cotton items.This programme removesmicro-organisms
2) The Stain function is not available with a temperature lower than 40°C.3) If you select the Extra Quick duration, we recommend that you decrease th
7. CONSUMPTION VALUESAt programme start the display shows the duration programme for the max-imum load capacity.During the washing phase the programme
2.Put a small quantity of detergent inthe main wash compartment of thedetergent dispenser. Set and start aprogramme for cotton at the highesttemperatu
The detergent compartment for the washing phase.If you use a liquid detergent, put it immediately before you startthe programme.Liquid additives compa
5.Measure out the detergent and thefabric conditioner.6.Carefully close the detergent dis-penser. Make sure that the flapdoes not cause a blockage whe
To open the appliance door:1.Press button 4 . The door locksymbol in the display goes off.2.Open the appliance door.3.Close the appliance door and pre
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
• Wash with a special detergent heavysoil stains.• Be careful with the curtains. Removethe hooks or put the curtains in awashing bag or pillowcase.• D
11.1 DescalingThe water we use contains limescale. If itbecomes necessary, use a water softenerto remove limescales.Use a special product made for was
3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put back the dispe
3.Put a container below the recess ofthe drain pump to collect the waterthat flows out.4.Press the two levers and pull for-ward the drainage duct to l
To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif
12. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta
Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T
Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai
2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from
127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for
13.4 The inlet hose20O20O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rect
Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t
• If the end of the drain hose is this (seethe drawing), you can push it directlyinto the stand pipe.Without the plastic hose guide.• To a sink spigot
13.6 In the interest of the environment• Connect the appliance to the FOULsystem for the drain water. The sew-age works keeps the drain water forthe t
ENGLISH 35www.devicemanuals.eu
www.aeg.com/shop132927781-A-052013www.devicemanuals.eu
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
mains plug, use a 13 amp ASTA (BS1362) fuse.•This appliance complies with theE.E.C. Directives.Water connection• Make sure not to cause damage to thew
Level of protection against ingress of solid particlesand moisture ensured by the protective cover, ex-cept where the low voltage equipment has no pro
4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
5.1 AUTO Off button 1Press this button to activate or deacti-vate the appliance. A tune sounds whenthe appliance is activated.The AUTO OFF function au
The phase symbols• When a programme is set, all the symbols of the phases related tothe programme come on.• When the programme starts, only the symbol
Comments to this Manuals