Aeg GAS HOB 84602 G User Manual

AUS ERFAHRUNG GUT84602 G - 85600 G - 856001 GGas hobTable de cuissonKochmuldeGaskookplaatPiano di cotturaOperating InstructionsNotice d’utilisationGeb

10Service and Spare PartsWhen you contact the Service Centre, they will need the followinginformation:1. Your name, address and post code.2. Your te

11Guarantee ConditionsAEG offer the following guarantee to the first purchaser of this appliance.1. The guarantee is valid for 12 months commencing wh

12OVERALL DIMENSIONS Width: 580 mm.Depth: 510 mm.Height: 88 mm.Weight: 8 Kg.CUT OUT DIMENSIONS Width: 550 mm.Depth: 470 mm.Thickness: 30 mm.SUPPLY CO

13BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1

14Important safety requirementsThis hob must be installed in accordance with the Gas Safety(Installation and Use) Regulations (Current Edition) and th

15650 mm420 mm420 mm100 mm50 mm50 mm55 mm600 mm700 mm420 mm100 mm420 mm50 mm55 mm50 mmCLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOO

16A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the GJ 1/2" threaded elbow,adjustment is fixed s

1755047058051055 min.FO 2272Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob

18ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must betaken in designing th

19Fitting the hob to the worktopBefore fitting the hob intothe cut out, an adhesive sealmust be fitted to theunderside outside edge of thehob. It is e

2Important Safety InformationYou MUST read these warnings carefully before installing or using thehob. If you need assistance, contact our Customer Ca

20Electrical connectionsAny electrical work required to install this hob should be carried outby a qualified electrician or competent person, in accor

21Permanent ConnectionIn the case of a permanent connection, it is necessary that you installa double pole switch between the hob and the electricity

22Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x1 scale and adjust zero if necessary.— Test leads from

24Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

25CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)

26Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gasbut can be converted for use with buta

3● When in use a gas cooking hob will produce heat and moisture in theroom in which it has been installed. Ensure there is a continuous airsupply, kee

4ContentsImportant Safety Information... 2Instructions for the User...

5This appliance is manufactured according tothe following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC,current edition.G

61. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burn

7HOB BURNERSTo light a burner, turn the relevant control knob anticlockwise to themaximum position, then push it down to ignite the burner. Upon,ignit

8Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is s

9Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local AEG Service Force Centre