AEG L7FE7461BI User Manual

USER MANUALEN User ManualWashing MachineL7FE7461BI

The inlet hose1. Remove the inlet hose from inside thedrum.2. To connect the water inlet hose towardsthe proper direction and with the properinclinati

Ø 40 mmTo a stand pipe with vent-holeDirectly into a drain pipe at a height of notless than 60 cm (23.6”) and not more than 100cm (39.3”).The end of t

553 mm596 mm140 mm76 mm50 mm50 mm819 mmIf hoses run behind theappliance, make sure thatnothing closes the smallrecess indicated with themeasures 50 x

1. Remove the screws of the top cover on therear of the appliance and install the anti-tilting device as shown in the drawing.~10mm2. Adjust the anti-

Reversibility of the cupboard doorCarry out the cupboard door reversibilitybefore the appliance is built in completely.MNOIf the cupboard door has to

16-22 mm22±1,5 mm449mm595-598 mmØ 35 mm12,5 - 14 mmSet the position of the lower hole respectingdimensions and distances shown in thedrawing (449 mm).

2N1EDCCounter-magnetThe appliance is pre set for a magneticclosure.For a correct closure:1. Position the screw C and the counter-magnet D on the magne

5. CONTROL PANEL5.1 Control panel descriptionStart/Pause90°60°40°30°20°ColdNight14001200800DelayStartTime SaveCottonsSyntheticsDelicatesAnti-allergySt

Delay start indicator.The digital indicator can show:• Reset position ( ).• Programme duration (e. g. ).• Delay time (e. g. ).• Cycle end ( ).• Warn

dashes to indicate that no programmewas selected.6.4 Temp. When you select a washing programme,the appliance automatically proposes adefault temperatu

CONTENTS1. SAFETY INFORMATION...32. SAFETY INSTRUCTIONS...

Recommended when you use fabricsoftener.This option increases theprogramme duration.The corresponding indicator above thetouch button illuminates and

very quick cycle for a smaller lightlysoiled load (max. half loadrecommended). the shortest cycle to freshen up asmall amount of laundry.The Time Sav

ProgrammeDefault tem-peratureTemperaturerangeReferencespin speedMaxi-mumloadProgramme description(Type of load and soil level)Synthetics40 °C60 °C - C

ProgrammeDefault tem-peratureTemperaturerangeReferencespin speedMaxi-mumloadProgramme description(Type of load and soil level)Special programmesSpin/D

ProgrammeDefault tem-peratureTemperaturerangeReferencespin speedMaxi-mumloadProgramme description(Type of load and soil level)Outdoor30 °C40 °C - Cold

ProgrammeDefault tem-peratureTemperaturerangeReferencespin speedMaxi-mumloadProgramme description(Type of load and soil level)Wool/Silk40 °C40 °C - Co

Programme Spin Rinse HoldNospin Quiet Prewash1) 2) Soft Plus Plus Steam2) Delay Start Time SaveSteam Spin/Drain 3)

8. SETTINGS8.1 Acoustic signalsThis appliance has different acousticsignals, that operate when:• You activate the appliance (specialshort tune).• You

CAUTION!Make sure that no laundrygets caught between theseal and the door to avoidrisk of water leakage anddamage to the laundry.Washing heavily oiled

• Do not exceed to liquiddetergent dose indicated on theflap.• Do not set the prewash phase.• Do not set the delay startfunction.5. Measure out the de

1. SAFETY INFORMATIONBefore the installation and use of the appliance,carefully read the supplied instructions. Themanufacturer is not responsible f

10.8 The ProSense Systemload detectionAfter touching the Start/Pause button:1. The ProSense System startsestimating the weight of the load tocalculate

4. Keep the door and the detergentdispenser slightly ajar to preventmildew and odours.5. Close the water tap.10.13 Draining water out afterend of cycl

• Use a washing bag to wash smalland/or delicate items (e.g. underwiredbras, belts, tights, etc. ).• A very small load can cause balanceproblems with

12. CARE AND CLEANINGWARNING!Refer to Safety chapters.12.1 External cleaningClean the appliance with mild soap andwarm water only. Fully dry all thesu

12.6 Cleaning the detergentdispenserTo prevent possible deposits of drieddetergent or clotted fabric softenerand/or formation of mould in thedetergent

WARNING!• Do not remove the filterwhile the applianceoperates.• Do not clean the pump ifthe water in theappliance is hot. Waituntil the water coolsdow

126. Turn the filter anti-clockwise to remove it7. If it is necessary, remove fluff and objectsfrom the filter recess.Make sure that the impeller of t

1210. Close the pump cover.When you drain the water with the emergency drain procedure, you must activate the drainsystem again:1. Put 2 litres of wat

12.10 Frost precautionsIf the appliance is installed in an areawhere the temperature can reach valuesaround 0° C or drop below, remove theremaining wa

13.2 Possible failuresProblem Possible solutionThe programme doesnot start.• Make sure that the mains plug is connected to the mainssocket.• Make sure

– staff kitchen areas in shops, offices and otherworking environments;– by clients in hotels, motels, bed & breakfast andother residential type en

Problem Possible solutionThe spin phase does notoperate or the washingcycle lasts longer thanusual.• Set the spin programme.• Make sure that the drain

After the check, activate the appliance. The programme continues from the point ofinterruption.If the problem occurs again, contact the Authorised Ser

Programmes Load(kg)Energyconsump-tion (kWh)Waterconsump-tion (litre)Approxi-mate pro-grammeduration(minutes)Remain-ing mois-ture (%)1)Cottons60°C7 1.2

Water supply pressure1)MinimumMaximum0.5 bar (0.05 MPa)8 bar (0.8 MPa)Water supply 2)Cold waterMaximum Load Cotton 7 kgEnergy Efficiency Class A+++Spi

Spin-drying efficiency class on a scale from G (least effi-cient) to A (most efficient)BMaximum spin speed in rpm 1351Remaining moisture content in %

ENGLISH 45

www.aeg.com46

ENGLISH 47

www.aeg.com/shop157020291-A-462018

• Do not use the appliance beforeinstalling it in the built-in structure.• Do not install or use a damagedappliance.• Do not install or use the applia

substances. It can damage rubberparts of the washing machine.Prewash such fabrics by hand beforeloading them into the washingmachine.• Do not touch th

3.3 UnpackingWARNING!Use the gloves.WARNING!Remove all the packaging and the transit bolts before installing theappliance.1. Put two polystyrene packa

5. Remove the power supply cable andthe drain hose from the hose holders.It is possible to see waterflowing from the drainhose. This is due to thetest

3.5 Positioning and levellingx41. Install the appliance on a flat hard floor.WARNING!Make sure that carpets do notstop the air circulation belowthe ap